SST-40-EIH 2025 Ford F-550 4×4 BrandFX

VERSALIFT SST-40-EIH – AERIAL PLATFORM LIFT SPECIFICATIONS

• Type: Insulated end-mounted 40 ft. (12.2 m) telescopic aerial platform lift
• Working Height: 45 ft. (13.7 m)
• Horizontal Reach: 27 ft. 9 in. (8.5 m)
• Frame Height: 40 in.

Platform

• Fiberglass, 24 in. × 30 in. × 42 in. (0.61 m × 0.76 m × 1.07 m)

• Inside and outside step for access

• Capacity: 350 lbs. (160 kg)

• Tubular rubber support provided

• Rotating Platform: 180° hydraulic rotation

• Hydraulic Tool Circuit: 5 gpm (19 lpm) at 2250 psi (158 kg/cm²), open-center tools

• Platform Liner & Cover: 50 kV rated liner, soft vinyl cover

• Personnel Restraint: Arc flash rated harness and lanyard

Controls

• Single Stick 3-Axis Platform Control: Multi-jointed handle, safety trigger, full pressure/flow, emergency stop

• TRUGUARD™: 4″ electrical isolation of upper controls with protective shield

• Hydraulic Platform Leveling: Master/slave cylinder; operable from upper controls

Boom Assembly

• Outer/Inner Boom: Outer boom: 6×8 in. steel & 7.5×9.5 in. fiberglass (Electroguard), 42 in. insulation gap

• Inner Boom: 5×7 in. rectangular fiberglass, telescopic extension, fully contained non-conductive hoses

• Boom Articulation: 14° below to 74° above horizontal

• Compensated Lower Boom: 6 in. square steel, 5° below to vertical, parallelogram linkage

• Chassis Insulation System: Fiberglass insert, 12 in. insulation gap, ANSI A92.2 tested

Mechanical & Hydraulic Components

• High-strength chrome-plated pins, bolted and capped for redundancy

• Outer & lower boom cylinders: Threaded end-cap design, holding valves

• Turret: Steel wings, welded tube support, machined bearing plate, bearing cover

• Continuous rotation: Hydraulic worm & spur gear, electric/hydraulic collector rings, manual override

• Hydraulic system: 5 gpm (18.9 lpm) at 2250 psi, 100-mesh suction screen, 10-micron return filter

• Hoses & fittings: Non-conductive, high-pressure, swaged ends, nylon sleeves at movement points

• Engine Start/Stop & Master Control: Requires truck ignition + master switch

• Automatic Throttle Control: Increases idle when PTO engaged

• Backup Pump: 12V DC motor-driven auxiliary pump

Electrical & Safety

• Electrical insulation: Certified for 46 kV per ANSI A92.2

• TRUGUARD™ isolation for upper controls

• Slope indicators included

• Paint: White urethane, primed prior to assembly

Manuals Included

• 2 × Operator’s Manuals

• 2 × Service Manuals

• 1 × Manual of Responsibilities

• 1 × EMI Safety Manual

Chassis Specifications (Non-California Sale)

• 2025 Ford F-550 Reg Cab 4×4

• 6.7L 4V V8 Turbo Diesel Engine, 10-Speed Automatic

• Limited Slip w/4.30 Axle Ratio

• GVWR: 19,500 lbs.; GAWR Front: 7,000 lbs.; Rear: 14,706 lbs.

• Tires: 225/70RX19.5G BSW Front & Rear

• Interior: HD Vinyl 40/20/40 Split Bench, Medium Earth Gray

• Exterior: Oxford White

• Features: AM/FM w/SYNC, Power Windows/Locks, Keyless Entry, Dual 350A Alternators, Engine Block Heater, PTO Provision, Rear View Camera & Prep, Trailer Brake Controller, High-Capacity Tow Package, Steering Wheel Cruise Control

Body Specifications (BFXB 84DLS W/ C2 WU Service Body)

• Compartments: Multiple adjustable shelves, divider packs, non-skid tops, clear vinyl rock guards

• Materials: Smooth aluminum bulkhead, aluminum tread floors, stainless steel hardware

• Doors: One-piece molded with automotive finish, recessed jambs, vinyl-covered stops

• Lighting: Full LED package (stop/tail/turn/marker/back-up), hotstick doors/shelves

• Additional: Wheel chock holders, cable stirrup steps, 6″ recycled plastic tailboard, hook packages

Installation & Accessories

• Mounting hardware, PTO, pump, VERSALIFT SST-40-EIH installation

• Hydraulic diagnostic test ports, park brake interlock, slope indicators

• Backup alarm, 4-corner LED strobe system, rear under-frame torsion bar

• Combo pintle/hitch with 2” ball & safety D-rings, ICC rear bumper, 7-prong flat-pin trailer receptacle

• Mud flaps, travel height decal, paint body to match cab/chassis

• Black non-skid treadplate floor, fire extinguisher, 3-piece triangle reflector kit

• Two rubber wheel chocks

• Test ride: 1 hour, ANSI A92.2-2021 certification