VERSALIFT VST-55-HDI, insulated 54 ft. 7 in. (16.6 m) articulating, telescopic aerial platform lift, 59 ft. 7 in. (18.2 m) working height with a horizontal reach of 33 ft. 5 in. (10.2 m) and to include the following items:
- Standard platform capacity of 600 lbs
- TruGuard™ dielectric isolating system with right hand single-stick control. All control handles are isolated and tested per ANSI 92.2. The high resistive dielectric system is protected from direct environmental and job related contamination. TruGuard™ technology incorporates the use of full hydraulic controls with durable metal handles and linkages
- Hydraulic platform rotator
- Hydraulic dual arm articulating jib pole and winch package for up to 1,000 lbs. (454 kg.) capacity, including insulated jib pole
- 360o continuous rotation including slip rings
- Six GPM (22.7 LPM) open center hydraulic system with a 3000 psi (210 kg/cm²) operating pressure
- Side mounted telescopic upper boom allows low stowing of platform. Fiberglass inner boom provides insulation gap of 54 inches (1.4 m) fully retracted meeting ANSI A92.2 requirements for Category C 46KV and below
- Chassis insulating system (fiberglass lower boom insert) providing 12 in. (0.305 m) insulation gap and including accommodations to bridge insulation gap for testing per ANSI 92.2
- Inner boom finished with white urethane paint over a white gel coat
- Non-lube bearings used throughout
- One set of hydraulic tool outlets with pressure limit valve. Valve can be adjusted from 1000 to 2500 psi
- Sub frame mounted main A-frame outriggers with pivot feet, two control valves, and a selector valve
- Auxiliary independent narrow knock down A Frame outriggers with pivot feet
- Outrigger boom interlock system for main and auxiliary outriggers
- Integral reservoir with a 17-gallon (64.4 l) capacity and dual sight gauges
- Side mounted closed heavy-duty one-step 24 in. X 48 in. X 42 in. (0.61m X 1.22m X 1.07m) fiberglass platform including platform liner and vinyl cover
- Individual full pressure controls at the turret actuate all boom functions and is equipped with a selector valve to override upper controls
- 12 volt DC backup pump providing power to all boom functions
- Automatic throttle control
- Auto boom latch for mounting on inner boom. The rotary auto boom latch works off the lift hydraulic pressure to open and close
- Standard white urethane paint
- Safety harness and lanyard
- Two operator manuals and service manuals
Cab and chassis to the following specifications:
- 2023 International CV 4×4 cab and chassis with a CA of 84”
- GVWR: 22,500 lbs
- International 6.6L diesel engine
- Allison 2750 RDS 6-speed automatic transmission
- Engine block heater and back up alarm
- 40 gallon fuel tank mounted between frame rails and behind rear axle
- Power windows and keyless remote entry system
- Air conditioning
- 225/70R19.5 load range G HDR tires
- Radio AM/FM stereo/clock/Bluetooth with 7” touch panel display
- Painted Winter White
- Full specifications are available
BFX Bodies 132” long x 42” high x 94” wide service body including the following:
- 30 inch aluminum tread plate platform extension
- BFX LED lighting package installed in tail shelf
- Cable access step at rear and side access
- Two (2) stainless steel grab handles at side access and two (2) aluminum grab rails at rear tail shelf
- Wheel chock storage and outrigger pad holders
- Push/pull rod lock system
42” High Street side compartments as follows:
- 1st Vertical: Two (2) adjustable shelves with dividers and cutout for outrigger
- 2nd Vertical: Two (2) adjustable shelves with dividers
- Horizontal: One (1) removable shelf with dividers
- Rear Vertical: Two (2) adjustable shelves with dividers
- 132” x 18” x 11” fiberglass hotstick top box with door at rear
42” High Curbside compartments as follows:
- 1st Vertical: Two (2) adjustable shelves with dividers and cutout for outrigger
- 2nd Vertical: Gripstrut access steps to bed area with removable composite side gate
- 3rd Vertical: Two (2) adjustable shelves with dividers
- Horizontal: One (1) adjustable shelf with dividers
- Rear Vertical: Five (5) fixed material hooks 1-3-1
Installation to include the following:
- Install VERSALIFT VST-55-HDI, mounting hardware, PTO and pump
- Install service body and accessories
- Install combo pintle hitch, D rings and 7 prong trailer connector
- Install two (2) amber strobe lights in tail shelf and two (2) strobe lights in front grill
- Install grounding kit, park brake interlock system, back up alarm and mud flaps
- Supply outrigger pads, wheel chocks, fire extinguisher, and 3 piece triangle reflector kit
- Test ride completed unit for one (1) hour
- Test and certify per ANSI A92.2